• Float-operated, submersible, 2-pole mechanical switch integrating advanced switch technology

• Corrosion-resistant, powder coated epoxy finish

• All cast iron construction

• Viton outer switch boot

• No sheet metal parts to rust or corrode

• Stainless steel screws, switch arm, guard and handle

• No screens to clog

• Watertight, neoprene square ring between motor and pump housing

• Solid, buoyant, polypropylene float

• Oil-filled, hermetically-sealed, automatic reset thermal overload protected motor

• Upper and lower sleeve bearings running in bath of oil

• Entire unit pressure-tested after assembly

• Carbon and ceramic shaft seal

• Maximum temperature for effluent or dewatering: 130 °F (54 °C)

• Passes 1/2” (12 mm) spherical solids

• 1-1/2” NPT discharge

• On point: 7-1/4” (18 cm)

• Off point: 3” (8 cm)

• Major width: 10-3/32″ (26.2 cm)

• Major height: 10-1/16″ (25.6 cm)

• Watertight and dust-tight

• Permanently oiled bearings

• Cast iron impeller

• 5 year limited warranty

• Float-operated, submersible, 2-pole mechanical switch integrating advanced switch technology

• Corrosion-resistant, powder coated epoxy finish

• All cast iron construction

• Viton outer switch boot

• No sheet metal parts to rust or corrode

• Stainless steel screws, switch arm, guard and handle

• No screens to clog

• Watertight, neoprene square ring between motor and pump housing

• Solid, buoyant, polypropylene float

• Oil-filled, hermetically-sealed, automatic reset thermal overload protected motor

• Upper and lower sleeve bearings running in bath of oil

• Entire unit pressure-tested after assembly

• Carbon and ceramic shaft seal

• Maximum temperature for effluent or dewatering: 130 °F (54 °C)

• Passes 1/2” (12 mm) spherical solids

• 1-1/2” NPT discharge

• On point: 7-1/4” (18 cm)

• Off point: 3” (8 cm)

• Major width: 10-3/32″ (26.2 cm)

• Major height: 10-1/16″ (25.6 cm)

• Watertight and dust-tight

• Permanently oiled bearings

• Cast iron impeller

• 5 year limited warranty

• Oil-filled, hermetically-sealed motor with automatic reset thermal overload protection

• Rugged, cast iron motor housing with corrosion-resistant, baked-on enamel finish

• Efficient heat sink for heat dissipation

• Engineered plastic base and pump housing with no screen

• Passes 3/8” (9 mm) spherical solids

• Reliable integrated vertical switch

• Carbon and ceramic rotary seal

• Watertight, NBR rubber seal between motor and cover

• Stainless steel screws and hardware

• Temperature rating: 104 °F (40 °C)

• On point: 6-1/2” (16.5 cm)

• Off point: 2-1/2” (6.3 cm)

• Maximum width: 8-3/32″ (21 cm)

• Maximum height: 11″ (27.9 cm)

• Weight: 12.4 lbs (5.6 kg)

• Fits 12″ (30 cm) diameter pits

• 100% factory tested after assembly

• 2 year limited warranty

• Extra protection when your primary pump fails for any reason

• No interruption in pump performance because of power outage or failure of primary pump

• One of the most reliable and well-established battery backup systems in use today

• 25 years of proven performance in the field and thousands of satisfied customers

• Pump has heavy-duty, 12 V motor and positive contact float switch

• Stainless steel column and shaft

• Non-corrosive base assembly

• Discharges water as fast as many 1/3 HP primary pumps

• Aquanot® II equipped with automatic electronic 28.0 amp charger to maintain and recharge battery

• Pump alarm included

• Minimum pit requirements: 18″ x 22″ (46 x 56 cm)

For AC pump backup and emergency use.

The Complete Aquanot® II system includes the pump, the electronic charger and a 12 V pump alarm. You may purchase the DEEP-CYCLE battery and battery box separately.

Aquanot® II comes with these electronic charger features:

• 28.0 amp battery charger

• LED status indicators

• Automatic battery recharging

• Microprocessor controlled

• Each unit individually tested

• 3.5 amp AC input

• 12 V DC output

• Because this unit converts AC to DC, this pump will operate for an extended time as a backup unit in case of primary pump failure